Old code used `cfg_if!` because rustc still parses code inside disabled cfg's, and Rust stable at that time couldn't parse the new GAT where-clause location. This is not the case anymore.
876: Add defmt support to embassy-embedded-hal errors r=Dirbaio a=matoushybl
`defmt::unwrap!()` should now work with shared buses. I tested it only with I2C as I don't have SPI in the target project.
Co-authored-by: Matous Hybl <hyblmatous@gmail.com>
550da471be previously refactored the STM32
PWM logic in such a way to preclude use of non-contiguous channels (e.g.
channel 2 but not channel 1). Refactor it yet again to yet again allow
this sort of usage.
866: F4 flash fixes r=Dirbaio a=chemicstry
This discontinuous flash sector layout is too cursed and I left some mistakes in last PR. Erasing last sector did not work and it wasn't possible to erase between memory banks for 1MB dual-bank devices. So I changed the erase function to iterate over memory addresses (which is continuous) instead of sector numbers.
It should also be possible to implement erase across memory banks for H7, but it requires special handling for write too. I don't have an H7 to test now so left it as is.
I wasn't sure how to add tests to `embassy-stm32` and it seems that there are none, except for `subghz`, but no test runner? Anyway, I tested the `get_sector` on playground: https://play.rust-lang.org/?version=stable&mode=debug&edition=2021&gist=13b59339fe6c70a3249e6183e81f869e
Also fixed erase alignment requirements on `Flash::blocking_erase()`, as it previously only checked alignment on size, but not on offsets.
P.S. the diff is a bit messed up, I recommend looking at files directly
Co-authored-by: chemicstry <chemicstry@gmail.com>
858: embassy-stm32: Simplify time r=Dirbaio a=GrantM11235
- Remove unused `MilliSeconds`, `MicroSeconds`, and `NanoSeconds` types
- Remove `Bps`, `KiloHertz`, and `MegaHertz` types that were only used
for converting to `Hertz`
- Replace all instances of `impl Into<Hertz>` with `Hertz`
- Add `hz`, `khz`, and `mhz` methods to `Hertz`, as well as
free function shortcuts
- Remove `U32Ext` extension trait
Co-authored-by: Grant Miller <GrantM11235@gmail.com>
- Remove unused `MilliSeconds`, `MicroSeconds`, and `NanoSeconds` types
- Remove `Bps`, `KiloHertz`, and `MegaHertz` types that were only used
for converting to `Hertz`
- Replace all instances of `impl Into<Hertz>` with `Hertz`
- Add `hz`, `khz`, and `mhz` methods to `Hertz`, as well as
free function shortcuts
- Remove `U32Ext` extension trait
810: Takes care of power for nRF USB devices r=Dirbaio a=huntc
Modifies the usb-serial example to illustrate how to setup USB for situations where the USB power can be detected and removed.
Gaps:
~~* No support for the nrf-softdevices as yet, although this should be possible via another constructor.~~
* No support for the nrf5340, although this should be possible via USBREG.
The change is tested and appears to work. Some notes:
* There's an existing field named self_powered as a UsbDevice field. It doesn't ever appear to get set. I'm wondering if this field is intended to signal that a device has the nRF VBUS power situation or not. I'm not presently using it.
* The new PowerDetected event is generated on the bus initially in situations where just new is used i.e. without power management, including on STM. We can therefore rely on this event always being generated.
Old description:
~~EnabledUsbDevice is a wrapper around the `UsbDevice` where its enablement is also subject to external events, such as `POWER` events for nRF. It is introduced generically to support other platforms should they also require external signaling for enablement.~~
Co-authored-by: huntc <huntchr@gmail.com>
854: Implement IWDG timeout calculation r=Dirbaio a=chemicstry
Allow specifying `IndependentWatchdog` timeout as `Duration` instead of prescaler value.
Since IWDG is clocked from LSI, which differs between families, I standardized HSI/LSI definitions in RCC and used that.
Co-authored-by: chemicstry <chemicstry@gmail.com>
851: Gpio dynamic flex r=Dirbaio a=AntoineMugnier
Add Flex GPIO type for embassy-stm32 as it is the case for embassy-nrf.
Co-authored-by: amugniere@gmail.com <antoine.mugnier@depixus.com>
