don't recalculate clock frequencies every time they are asked for. while
this is not very often in practice it does consume a bunch of flash
space that cannot be optimized away, and was pulled in unconditionally
previously. while we technically only need the configured rosc, xosc and
gpin frequencies it is easier to store all frequencies (and much cheaper
at runtime too).
if rosc really does run at 140MHz in high at div=1 then these values
were not correct and would've exceeded the chip spec. the HIL test
device seems to run fast (150MHz) so they're still not quite correct,
but rosc has high variance anyway so it's probably fine.
exposing pac items kind of undermines the unstable-pac feature. directly
exposing register structure is also pretty inconvenient since the clock
switching code takes care of the src/aux difference in behavior, so a
user needn't really be forced to write down decomposed register values.
the datasheet says that the xosc may be run by feeding a square wave
into the XIN pin of the chip, but requires that the oscillator be set to
pass through XIN in that case. it does not mention how, the xosc
peripheral does not seem to have any config bits that could be set to
this effect, and pico-sdk seems to have no (or at least no special)
handling for this configuration at all. it can thus be assumed to either
be not supported even by the reference sdk or to not need different
handling.
solvers usually output fbdiv directly, using vco_freq to get back to
fbdiv is not all that necessary or useful. both vco_freq and fbdiv have
hidden constraints, but vco_freq is a lot less accurate because the
fbdiv value resulting from the division may be off by almost a full
ref_freq's worth of frequency.
also fixes the usb pll config, which ran the pll vco way out of (below)
spec.
we might not configure both, so we should put the others into reset
state. leaving them fully as is might leave them running, which might
not be the goal for runtime reconfig (when it comes around). this now
mirrors how we reset all clock-using peripherals and only unreset those
that are properly clocked.
this is only really useful for runtime *re*configuration, which we don't
currently support. even runtime reconfig probably won't need it, unless
we keep taking the sledgehammer approach of reconfiguring everything all
the time.
1459: rp/multicore: fix undefined behavior in multicore spawn. r=Dirbaio a=Dirbaio
It is UB to pass `entry` to core1 as `&mut`, because core0 keeps an aliasing pointer to that memory region, and actually writes to it (when `spawn_core1` returns, the stack frame gets deallocated and the memory gets reused). This violates noalias requirements.
Added the fence just in case, een though it works without.
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
It is UB to pass `entry` to core1 as `&mut`, because core0 keeps
an aliasing pointer to that memory region, and actually writes to
it (when `spawn_core1` returns, the stack frame gets deallocated and the memory
gets reused). This violates noalias requirements.
Added the fence just in case, een though it works without.
1458: rp: remove take!, add bind_interrupts! r=Dirbaio a=pennae
both of the uart interrupts now check a flag that only the dma rx path ever sets (and now unsets again on drop) to return early if it's not as they expect. this is ... not our preferred solution, but if bind_interrupts *must* allow mutiple handlers to be specified then this is the only way we can think of that doesn't break uarts.
Co-authored-by: pennae <github@quasiparticle.net>
1456: net: do not use smoltcp Instant/Duration in public API, docs. r=Dirbaio a=Dirbaio
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
1451: Work around xtensa deadlock, take 2 r=Dirbaio a=bugadani
This PR is another go at trying to do something with #1449. The commit was part of the previous attempt but mistakenly discarded as I still experienced lockups. However, after further testing, it looks like that lockup is caused by something else.
This is a manual, "cpu-local" critical section impl that should be good enough on dual-core CPUs, although the implementation still contains `SIGNAL_WORK_THREAD_MODE` which is absolutely not correct on dual-core. This approach was chosen because:
- not taking the global lock technically allows the second core to run
- wrapping the signal read and the sleep in a critical section prevents a race condition that would cause the CPU to sleep longer than ideal if an interrupt hits after reading, but before sleeping.
Co-authored-by: Dániel Buga <bugadani@gmail.com>
1454: stm32f0 flash implementation r=Dirbaio a=jp99
i've copied and modified the f3 implementation and it seems to be working.
Co-authored-by: Jaap Prickartz <jaap@tetra.nl>
1453: stm32 uart: Fix error flag handling for blocking operations r=Dirbaio a=timokroeger
Clear and report the error flags one by one and pop the data byte only after all error flags were handled.
For v1/v2 we emulate the v3/v4 behaviour by buffering the status register because a read to the data register clears all flags at once which means we might loose all but the first error.
Only tested on stm32f3 discovery board with loopback. Let‘s see what CI says for the other families.
Fixes#1452
Co-authored-by: Timo Kröger <timokroeger93@gmail.com>
Clear and report the error flags one by one and pop the data byte only
after all error flags were handled.
For v1/v2 we emulate the v3/v4 behaviour by buffering the status
register because a read to the data register clears all flags at once
which means we might loose all but the first error.
1448: rp: don't use SetConfig trait in PWM and PIO. r=Dirbaio a=Dirbaio
It was intended to allow changing baudrate on shared spi/i2c. There's no advantage in using it for PWM or PIO, and makes it less usable because you have to have `embassy-embedded-hal` as a dep to use it.
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
It was intended to allow changing baudrate on shared spi/i2c. There's no
advantage in using it for PWM or PIO, and makes it less usable because you have to
have `embassy-embedded-hal` as a dep to use it.
1447: rp/watchdog: fix overflow if period is longer than 4294 seconds. r=Dirbaio a=Dirbaio
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
1424: add TL maibox for stm32wb r=xoviat a=OueslatiGhaith
Hello,
This pull request is related to #1397 and #1401, inspired by #24, build upon the work done in #1405, and was tested on an stm32wb55rg.
This pull request aims to add the transport layer mailbox for stm32wb microcontrollers. For now it's only capable of initializing it and getting the firmware information
Co-authored-by: goueslati <ghaith.oueslati@habemus.com>
Co-authored-by: Ghaith Oueslati <73850124+OueslatiGhaith@users.noreply.github.com>
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
1436: rp: Clock configuration r=CBJamo a=CBJamo
Draft of a more complete clock config for the 2040.
I also extended and made public the clk_<name>_freq functions. I know at least the ws2812 pio example would like to get the sys clock at runtime rather than just using a constant. I suspect most pio-based peripherals will want access to the clocks.
Open questions:
1. Best way to handle the 3 external clock frequencies. I think the XIN (aka crystal) freq should just be set by the init function then never changed, though if it's an external clock that could change? I'm not sure anyone would ever want to do that but maybe it should be handled just in case? The other two should probably be set by the application.
2. Better estimation of ROSC frequency. Right now it's really just a lookup table of the speed from the single sample I did this testing on, and only uses the frequency range and div, drive strength is ignored.
3. Probably some kind of warning should be generated if the random bit from the rosc won't be useful, not sure how to do that.
4. Should clocks only be allowed to be configured at init, or should they be modifiable at runtime? For example, switching the RTC to a clock in pin when a pps source is available.
Bonus feature to support clock output. I only implemented the bare minimum, and only for gpout0. I'm sure there's a clean way with macros to impl all 4 without just copy/paste, but I haven't learned macros yet.
Co-authored-by: Caleb Jamison <caleb@cbjamo.com>
1439: rp: use rp2040-boot2 to provide the boot2 blob r=Dirbaio a=pennae
we're currently shipping an old boot2 that runs the flash at half speed. use the more recent version instead, and allow user to choose between the different supported boot2 versions for different flash chips if they need that.
Co-authored-by: pennae <github@quasiparticle.net>
