1457: TL Mbox read and write for stm32wb r=xoviat a=OueslatiGhaith
Hello,
This pull request is related to #1397 and #1401, inspired by #24, built upon the work done in #1405 and #1424, and was tested on an stm32wb55rg.
This pull request aims to add read and write functionality to the TL mailbox for stm32wb microcontrollers
Co-authored-by: goueslati <ghaith.oueslati@habemus.com>
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
1458: rp: remove take!, add bind_interrupts! r=Dirbaio a=pennae
both of the uart interrupts now check a flag that only the dma rx path ever sets (and now unsets again on drop) to return early if it's not as they expect. this is ... not our preferred solution, but if bind_interrupts *must* allow mutiple handlers to be specified then this is the only way we can think of that doesn't break uarts.
Co-authored-by: pennae <github@quasiparticle.net>
1424: add TL maibox for stm32wb r=xoviat a=OueslatiGhaith
Hello,
This pull request is related to #1397 and #1401, inspired by #24, build upon the work done in #1405, and was tested on an stm32wb55rg.
This pull request aims to add the transport layer mailbox for stm32wb microcontrollers. For now it's only capable of initializing it and getting the firmware information
Co-authored-by: goueslati <ghaith.oueslati@habemus.com>
Co-authored-by: Ghaith Oueslati <73850124+OueslatiGhaith@users.noreply.github.com>
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
1423: rp: fix gpio InputFuture and inefficiencies r=pennae a=pennae
InputFuture could not wait for edges without breaking due to a broken From impl, but even if the impl had been correct it would not have worked correctly because raw edge interrupts are sticky and must be cleared from software. also replace critical sections with atomic accesses, and do nvic setup only once.
Co-authored-by: pennae <github@quasiparticle.net>
doing this setup work repeatedly, on every wait, is unnecessary. with
nothing ever disabling the interrupt it is sufficient to enable it once
during device init and never touch it again.
1422: rp: remove leftovers from #1414 r=Dirbaio a=pennae
forgot to remove these when they were no longer necessary or useful. oops.
Co-authored-by: pennae <github@quasiparticle.net>
1376: rtc: cleanup and consolidate r=Dirbaio a=xoviat
This removes an extra file that I left in, adds an example, and consolidates the files into one 'v2' file.
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
this reports errors at the same location the blocking uart would, which
works out to being mostly exact (except in the case of overruns, where
one extra character is dropped). this is actually easier than going
nuclear in the case of errors and nuking both the buffer contents and
the rx fifo, both of which are things we'd have to do in addition to
what's added here, and neither are needed for correctness.
the rp uart receive fifo is 32 entries deep, so the 31 byte test data
fits into it without needing any buffering. extend to 48 bytes to fill
the entire fifo and the 16 byte test buffer.
rp-hal has done this very well already, so we'll just copy their entire
impl again. only div.rs needed some massaging because our sio access
works a little differently, everything else worked as is.
1321: executor: add Pender, rework Cargo features. r=Dirbaio a=Dirbaio
This introduces a `Pender` struct with enum cases for thread-mode, interrupt-mode and
custom callback executors. This avoids calls through function pointers when using only
the thread or interrupt executors. Faster, and friendlier to `cargo-call-stack`.
`embassy-executor` now has `arch-xxx` Cargo features to select the arch and to enable
the builtin executors (thread and interrupt).
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
This introduces a `Pender` struct with enum cases for thread-mode, interrupt-mode and
custom callback executors. This avoids calls through function pointers when using only
the thread or interrupt executors. Faster, and friendlier to `cargo-call-stack`.
`embassy-executor` now has `arch-xxx` Cargo features to select the arch and to enable
the builtin executors (thread and interrupt).
